-- Last Updated: Mar-28-14 11:05 PM EST --
Hey everyone I have a question about back bands and adjustment. I just recently bought a Perception Expression 15 and I'm almost done with my customization. I really like this boat and it fits me like a glove except for one thing, the seat back (which is pretty much everyone's one complaint about this boat). Although the seat is super comfortable I've decided to remove the back and install a band since the back sits so high even at it's lowest setting. My question is what is the optimal height and point of rest on the back for a band and should I also move the seat back closer to the cockpit rear or does that not matter? Thanks in advance.
First Need Purifier
Electric Kayak Motor
Touring Kayak Paddles
Full Size Sail Rig
Heel and Pegpads™
|Table of Contents|
|Messages in this Topic|
You want to be sitting erect|
Posted by: Celia on Mar-29-14 7:59 AM (EST)
The backband should be low enough to support your lumbar vertebrae into lower back maybe a little, but overall should be at a point where it helps you to stay erect and take advantage of your core muscles for primary support. That leaves you free to rotate properly for the forward stroke.
Posted by: Marshall on Mar-29-14 9:26 AM (EST)
Simple retrofit. Comes as a kit with multiple attachment methods.
I could take awhile.|
Posted by: magooch on Mar-29-14 9:58 AM (EST)
I wouldn't get too anxious about trying to find the right formula for what fits you best. Even the best setup will most likely take a little time to get used to. Over time, you will determine which changes you need to make and don't be discouraged if you have to make more changes as time goes on. I made several changes on one of my boats and finally worked my way back to pretty much the way it came, but with a minor change in some adjustment bungees that made all the difference in the world.
Depending on your seat hangers|
Posted by: randy_morgart on Mar-29-14 10:22 AM (EST)
You can use zip ties around or fender washers to clamp to the edge of the hanger and paddle w the backband in different positions to see what feels best. If using the washers on fiberglass hangers don't push too hard on the band or you could chip the hanger.
+1 on the IR band|
Posted by: trvlrerik on Mar-29-14 10:43 AM (EST)
I love the IR bands, easy retrofit. Going from a seat back to a back band does take time to get your core muscles adjusted and strengthened.
a recent thread on a similar topic|
Posted by: sapien on Mar-29-14 10:57 AM (EST)
that may provide you some good info; your Perception seat frame and attachment points are probably similar.
WS backband option|
Posted by: pbenter on Mar-29-14 2:00 PM (EST)
I switched out the seat back on my 2103 Tusnami 125 with the factory back band. It involved drilling out two factory marked holes in the rear coaming that do not go through to the outside. I am happy with the way it fits my lower back and allows for much better torso rotation. It stays out of the way when re-entering from a wet exit.
Posted by: jonnyboy on Mar-30-14 10:57 AM (EST)
Hey Paul, I ordered the same back band as well cause I wanted to stay factory and confluence has a video up on how to change the seat and band that I've found since my post. Thanks everyone else for the replies as well.
On my ww kayaks, I've tried to set |
Posted by: ezwater on Mar-29-14 2:39 PM (EST)
the backband height so that it is right at the top of my pelvis, but not on the vertebrae. For more relaxed use, a little higher might be OK, but the band should not inhibit torso rotation.
Posted by: Fred_Randall on Mar-29-14 8:32 PM (EST)
Big fan of the IR Loungeband. With a bit of care the installation is pretty easy. I put one in my Tsunami no problem.